Skip to main content

Jenkins - Git branch fallback with Git Chooser Alternative Plugin

If you need to have a fallback for your git branch selection in Jenkins, for example in case you're selecting branch for top project which has more subprojects. You can use Git Chooser Alternative Plugin. After installing it in Jenkins, you have to setup your Source Code Management section as follows:
Add two (or more) branches in to section "Branches to build". In example below, I'm using placeholders "primaryBranch" as a primary branch and "branch" as fallback one.
Then set strategy as "Alternative" and you're done!


Labels:

Comments

  1. research paper serviceSeptember 18, 2017 at 4:54 PM

    i have always struggled with these kind of technical things i am glad i got to stumble on your page. thank you for updating. keep posting it gives me a sense of calm that there is sonmeone to help out there

    ReplyDelete
  2. ArchanaMarch 31, 2022 at 1:48 PM

    Wow, it's a great write-up. To Hire a programmer initially, I also struggled a lot. Gradually I realised it's better to have expert assistance. Fortunately, the expert I got was from an emerging tech-based freelance platform,Eiliana.com who assisted me perfectly. I hired the right human resource, and I'm thankful to them.

    ReplyDelete

Post a Comment

Popular posts from this blog

IBUS with CC3D and CleanFlight/BetaFlight - Eachine 250 Racer

I finally managed to get IBUS working on my Eachine 250 Racer (ER250) and here's how! IBUS is digital communication protocol of FlySky/Turnigy controllers. I'm using FlySky FS-i6 with FS-iA6B receiver, but I guess you can use this guide also for SBUS and others. Connecting to CC3D  First, you need to use different connector. If you are currently using PWM or PPM on your receiver, you probably use 8 pin connector. For IBUS you need 4 pin FLEX or MAIN connector. Note: I don't use default ER250 position of CC3D, i rotated it -90°so I can access USB from the side. With ER250 you'll get the all needed cables. I already switched the connector on the receiver side so instead of 4 separate cables I have only 2 (blue is not connected). I'm using MAIN port, as FLEX port is on the side of battery tray in my settup. Black is GND, Red +5V, Yellow RX, Blue TX (not connected)  CleanFlight setup Note :  On older versions of CF/BF there is no
5 comments
Read more

Betaflight resource remapping with DSHOT

Since Betaflight 3.x.x there is possibility to remap your motor outputs. This allows you to use different pins in case some of them are broken. There are few tutorials on youtube how to remap your outputs, but I found only one, which takes into account DSHOT. Problem with remapping with DSHOT is that, not every flight controller output can be used as a DSHOT output. But how to find which output can be used for DSHOT? First, if you already made some changes to resources in CLI, revert them or re-flash your flight controller. Depending on your board, select the quadcopter type with same amount of motors as yours. I'm using SPRACINGF3EVO which has 8 motor outputs, so I selected "Octo Flat +" Go to the CLI and run command "resource" and then "resource list" Copy and whole output to the notepad You should get something as follows, with importrant parts in BOLD. # resource resource BEEPER 1 C15 resource MOTOR 1 A00 resource MOTOR 2 A01
4 comments
Read more

fordeals24.com is a scam

In case you get an email from fordeals24.com with a message that you bought something beware, it's a scam. Recently one of my friends got following (localized) email: Basically an order confirmation of buying some voucher which costs 80$. Interesting was that it had a valid name, phone and address. First we thought it's just a spam using some stolen database of contacts, but recently the goods actually arrived. Luckily he didn't accept the package. I didn't found any information online except this french reviews ( https://www.trustpilot.com/review/fordeals24.com ) saying basically the same, that they got packages just by filling contact form. Hope I stop someone from throwing away money.
2 comments
Read more